If the above command reports the error dd: bs: illegal numeric value, please change the block size bs=1m to bs=1M. Read the above step carefully to be sure you use the correct rdisk number here: sudo dd bs=1m if=-raspbian-jessie.img of=/dev/rdisk3 In the terminal, write the image to the card with this command, using the raw device name from above. For example, /dev/disk3s1 becomes /dev/rdisk3. Similarly, you might have another SD drive name/number like rdisk2 or rdisk4 you can check again by using the df -h command both before and after you insert your SD card reader into your Mac. Make sure the device name is the name of the whole SD card as described above, not just a partition of it - for example, rdisk3, not rdisk3s1. Using the device name of the partition, work out the raw device name for the entire disk by omitting the final s1 and replacing disk with rdisk This is very important, as you will lose all data on the hard drive if you provide the wrong device name. Do not eject it, or you will have to reconnect it. Unmount the partition so that you will be allowed to overwrite the disk: sudo diskutil unmount /dev/disk3s1Īlternatively, open Disk Utility and unmount the partition of the SD card. Record the device name of the filesystem’s partition, for example /dev/disk3s1. Run df -h again and look for the new device that wasn’t listed last time. Note: I had to use the rdisk naming convention but did not have to erase the SD card’s partition table.Ĭonnect the SD card reader with the SD card inside. I had to try the instructions marked “ALTERNATIVE METHOD”, which I quote immediately below this paragraph. Here are the instructions for burning it onto your micro-sd:įor me, using a macbook pro with MacOS 10.11.5 (El Capitan), the first part of the above instructions did not work. Load a Linux image on micro sd for the Pi (Jessie-lite) Obtain Jessie-lite Configure EMACS to work with SuperCollider.Configure the Pi to access your WiFi network and the internet.Connect the Raspberry Pi to the Computer via Ethernet, log onto the Raspberry Pi via ssh, and enable passwordless access using ssh-keygen.Download and store a Linux image on a micro sd disc, so as to boot the Raspberry Pi with it.The present instructions include the following steps: For later convenience, optionally, a WiFi network for connecting both the computer and the Raspberry Pi to the Internet.For initial connection, an Ethernet cable for connecting the Raspberry Pi to the computer, optionally via a switch.A computer equipped with an ethernet interface (the present instructions assume that you are working on a mac with MacOS 10.13 High Sierra and / or Manjaro Linux 17.0.6).A Raspberry Pi (The present instrucions are for Raspberry Pi 3 and Raspberry Pi 1 B+).The following items are needed to complete the setup: Subsequently it was tested on 3 and 4 November 2017 from a MacPro 2011 running manjaro linux 17.0.6, and on jessie lite on RPI 3 as well as stretch lite on RPI 1 B+. The procedure was first tested on using from a MacBook Pro 2013 running MacOS 10.12.1, using jessie lite on an RPI 3. The present instructions show how to set up the system of a Raspberry Pi on a micro-sd and to install Emacs and SuperCollider on it, using an Ethernet cable to connect to a computer and a WiFi network for access to the Internet. InstallationMedia: Ubuntu 22.Instructions for setting up a Raspberry Pi 3 for work with Emacs and SuperCollider over WiFi. InstallationDate: Installed on (5 days ago) This dialogue will close automatically after 5 minutes of inactivity. However, it asks this on every startup of the application, not remembering my selection in between launches.Īllow snap "youtube- music-desktop- app" to change "default- url-scheme- handler" subproperty "ytmd" to "youtube- music-desktop- app_youtube- music-desktop- app.desktop" ? I use a snap application (youtube- music-desktop- app) that wants to handle a particular URL scheme.
0 Comments
Leave a Reply. |